Skip to main content
10/100/1000base fiber optic media converter Installation
1. Interface
RJ-45 interface
the transmission media adopts CAT5 twisted-pair with typical length of 100 meters. It features the function of automatically identifying the through line and cross wire
Fiber interface
SC/ST fiber interface is of duplex mode type, including two interfaces, namely TX and RX. When the two sets of optical transceiver are interfaced or connected to switch with fiber interface, the fiber is in cross connection, namely "TX-RX", "RX-TX" (direct butting for single optical fiber).
fiber optic technician salary
2. Connection
The network device (work station, hub or switch) with RJ-45 interface is connected to RJ-45 jack of optical transceiver through twisted-pair. And the multi/single mode fiber is connected to SC/ST fiber interface of the optical transceiver. Then switch on. The corresponding LED is on for correct connection. (See the table below for the LED indicator lamp)

10/100/1000base fiber optic media converter Technical parameters:
1. Standard Protocol:
IEEE802.3 10 Base-T standard
IEEE 802.3u 100Base-TX/FX standard
IEEE 802.3z 1000Base-TX/FX standard
2.Connector:oneUTPRJ-45connector,oneSC/STconnector
3. Operation mode: full duplex mode or half duplex mode
4. Power supply parameter:
outside: 5V DC 2A
built-in: 110-265V AC  48VDC
5.Relative humidity: 5%-90%
6. TP cable: Cat5 UTP cable
7. Transfer fiber:
multi-mode: 50/125, 62.5/125 or 100/140μm
single mode:: 8.3/125, 8.7/125, 9/125 or 10/125μm

Comments

Post a Comment

Popular posts from this blog

The first transatlantic telephone cable to use optical fiber

The first transatlantic telephone cable to use optical fiber was TAT-8, based on Desurvire optimised laser amplification technology. It went into operation in 1988. Third-generation fiber-optic systems operated at 1.55 μm and had losses of about 0.2 dB/km. This development was spurred by the discovery of Indium gallium arsenide and the development of the Indium Gallium Arsenide photodiode by Pearsall. Engineers overcame earlier difficulties with pulse-spreading at that wavelength using conventional InGaAsP semiconductor lasers. Scientists overcame this difficulty by using dispersion-shifted fibers designed to have minimal dispersion at 1.55 μm or by limiting the laser spectrum to a single longitudinal mode. These developments eventually allowed third-generation systems to operate commercially at 2.5 Gbit/s with repeater spacing in excess of 100 km (62 mi). fiber optic technician certification The fourth generation of fiber-optic communication systems used optical amplification to
3 comments
Read more

What Are Backlinks?

     Backlinks (also known as “inbound links”, “incoming links” or “one way links”) are links from one website to a page on another website. Google and other major search engines consider backlinks “votes” for a specific page. Pages with a high number of backlinks tend to have high organic search engine rankings. https://plus.google.com/url?q=https%3A%2F%2Fhoneywebsolutions.com%2F https://plus.google.com/url?q=https%3A%2F%2Fwww.honeywebsolutions.com%2F https://plus.google.com/url?q=http%3A%2F%2Fhoneywebsolutions.com%2F https://www.google.com/url?q=https%3A%2F%2Fhoneywebsolutions.com%2F https://www.google.com/url?sa=t&url=http%3A%2F%2Fhoneywebsolutions.com https://www.google.com/url?sa=t&url=https%3A%2F%2Fhoneywebsolutions.com%2F https://maps.google.com/url?q=https%3A%2F%2Fhoneywebsolutions.com%2F https://maps.google.com/url?sa=t&url=http%3A%2F%2Fhoneywebsolutions.com https://images.google.de/url?q=https%3A%2F%2Fhoneywebsolutions.com%2F https://maps.google.de/url?q=https%3A%
1 comment
Read more

Radius of curvature

The radius of curvature of the cables must not be exceeded. The fiber optic cable may break when it twists or bends too much, especially during pulling. If there are no specific recommendations of the cable manufacturer, it should not be pulled at a radius of curvature less than 20 (twenty) times the diameter of the cable. When finished pulling, the cable should not have any radius of curvature less than 10 (ten) times the diameter of the cable. Vertical cable installations Whenever possible, it is better to lay the cables vertically down than to pull them up. Cables should be fastened at frequent intervals to avoid excessive tension in the jacket. They can be fastened with cable ties (well adjusted, but not enough to deform the cable jacket) or with Kellem type fasteners. Use the storage loops to help fix the cable and to provide cable for future repairs or re-installation. Internal plant wiring with trays Many times, the fiber optic cable in the wiring in the internal plan
Post a Comment
Read more